IN DEVELOPMENT · CLOSED BETARelease notes

PILOT GUIDE

Install AI_RADIO and
make your first radio call

A practical route from installation to transmission, with a phrase library to keep beside the cockpit.

RequirementsFirst-run checklistPhrase libraryRadio fundamentals

BEFORE YOU START

Windows, DCS and
audio requirements

The installer carries its own runtime and default local speech assets. No separate machine-wide .NET or Python installation is required.

OPERATING SYSTEMWindows 10 / 11 · x64
SIMULATORDCS World, installed and run once
INPUTA microphone + PTT binding
OPTIONALSRS transport · VoiceAttack compatibility

FIRST-RUN CHECKLIST

DCS hook, microphone
and PTT setup

Tick items as you work. This checklist stays in the current page; reloading resets it.

0 of 6 complete
AI_RADIO 0.9.110Controls → Bindings: an F/A-18C profile with separate HOTAS buttons for PTT Comm 1 and PTT Comm 2.
01

Install the beta

Read the release notes for your approved build. Use the MSI’s suggested writable location. The installer includes the default speech runtimes, model and voices.

02

Select the right DCS profile

Confirm the DCS installation and the Saved Games folder for the instance you use. Run DCS once first so that profile exists.

03

Connect the simulator

Close DCS, then use Install / Repair Hook in the DCS page. Normal integration lives in Saved Games. Follow the app’s restart or repair prompts.

04

Set up your audio

Select and enable your microphone in Audio. Choose the output device and confirm that you can hear a voice test. Begin with bundled local speech.

05

Bind push-to-talk

Choose PTT capture mode and bind an enabled keyboard or HOTAS button. Restart AI_RADIO after microphone/PTT changes so dispatch uses those settings.

06

Make the first call

Load a compatible mission, enter an aircraft, tune the agency’s frequency and key the intended radio. Follow the prompt: agency, callsign, request. Release PTT when finished.

EXAMPLE PHRASES

ATC, AWACS and tanker calls

Examples from the AI_RADIO command reference. Replace the agency and callsign with those in your mission. Only commands available in your current mission can be used.

19 phrases

Ground

Engine start

Nellis Ground, Hornet 1-1, request engine start.

Start with Ground at a supported airfield.

Ground

Taxi

Nellis Ground, Hornet 1-1, request taxi to runway.

Use the taxi command in the live Ground menu.

Tower

Departure

Nellis Tower, Hornet 1-1, ready for departure.

The current tower procedure must expose this command.

Tower

Winds

Nellis Tower, Hornet 1-1, say winds.

Tune the selected radio to Tower.

Tower

Overhead

Nellis Tower, Hornet 1-1, request the overhead.

Procedure availability is airfield-specific.

Approach

GCA

Nellis Approach, Hornet 1-1, request G C A.

Speak the letters individually.

Approach

IFR pickup

Nellis Approach, Hornet 1-1, request I F R pick up.

Use a compatible live approach menu.

Approach

Closed traffic

Nellis Approach, Hornet 1-1, request closed traffic.

The live menu determines eligibility.

Approach

ILS

Nellis Approach, Hornet 1-1, request I L S approach.

Say the letters separately.

C2

Check in

Goliath, Hornet 1-1, checking in.

Check in on the tactical net before using its tactical branch.

C2

Picture

Goliath, Hornet 1-1, picture.

The relevant tactical state must be available.

C2

Bogey dope

Goliath, Hornet 1-1, bogey dope.

Tune the appropriate tactical net.

C2

Declare

Goliath, Hornet 1-1, declare group one.

Group leaves appear only for existing groups.

C2

Say again

Goliath, Hornet 1-1, say again.

Use when exposed by the controller state.

C2

Fuel state

Goliath, Hornet 1-1, fuel state 14.4.

Use the primary-net fuel-state command.

C2

Fox Three report

Goliath, Hornet 1-1, Fox Three time out 30 seconds.

Use the live reporting command.

C2

Joker

Goliath, Hornet 1-1, joker.

Say “joker” without adding “fuel”.

C2

Bingo

Goliath, Hornet 1-1, bingo.

Say “bingo” without adding “fuel”.

Tanker

Air-to-air refuelling

Texaco 1-1, Hornet 1-1, request A A R.

Use the tanker and callsign in your mission.

JTAC and Wingman prompts depend on mission state; follow their live in-cockpit prompts. This curated library is a starting point, not a complete command catalogue.

HOW COMMANDS ARE SELECTED

Frequency, callsign and
available DCS commands

01

Call the right agency

Frequency scopes the command. Ground, Tower, Approach and tactical nets have different roles—even when labels look similar.

02

Use your callsign

WHO–WHO–WHAT: who you call, who you are, what you need. Follow the prompt for your aircraft identity.

03

Respect mission state

One PTT transmission executes one command. A phrase cannot activate an action absent from the live menu.

CONTACT THE DEVELOPER

Need help with audio, PTT or DCS integration?

Start with troubleshooting or prepare a support email. No account is required.

Open support

AI_RADIO application screenshot

Open original image ↗